Hc-sr501 Pir: 10 mejores de mayo de 2025

▼ Mostrar más▲ Mostrar menos

【Easy operation-1】 1. Sensing module for about a minute after power initialization time, during the interval to the output module 0-3 times a minute in standby mode. 2. Should avoid direct lighting such as interference sources close the surface of the lens module so as to avoid the introduction of interference signal generator malfunction; use of the environment to avoid the flow of the wind, the wind sensor will also cause interference.
【Easy operation-2】3. Sensor module using a dual probe, the probe's window is rectangular, dual (A per B million) in the direction of the ends of long, when the body passed from left to right or right to left when the reach the dual IR time, distance difference, the greater the difference, more sensitive sensors, when the body from the front to the probe or from top to bottom or from bottom to top direction passing, dual IR not detected changes in the distance.
【Easy operation-3】so the sensors should be installed dual direction of the probe with human activities as much as possible parallel to the direction of maximum to ensure that the body has been passed by the dual sensor probe. To increase the sensing range of angles, the module using a circular lens, the probe also makes sense on all four sides, by the above installation requirements.VCC, trig (control side), echo (receiving end), GND.
【Easy operation-4】5, with induction blocking time (the default setting: 2.5S block time): sensor module, after each sensor output (high change Into a low level),can set up a blockade followed by time period, in this time period the sensor does not accept any sensor signal. This feature can have a "sensor output time" and "blocking time" the interval between the work produced can be applied to detect the interval Products .
【Easy operation-5】6, the working voltage range: the default voltage DC4.5V-20V. 7, micro-power consumption: static current "50 microamps, especially for battery-powered automatic control products. !!Note!!: The potentiometer clockwise to adjust the distance, sensing range increases (about 7 meters), on the contrary, sensing range decreases (about 3 meters).Delay adjustment potentiometer clockwise rotation, sensor delay longer (about 300S), the other hand, induction by the short delay (about 5S)
7,76 € EN AMAZON

Hc-sr501 Pir

Los 10 mejores productos de mayo de 2025

Última actualización: 25 de mayo de 2025

SATKIT

Sensor de movimiento PIR HC-SR501 [Arduino Compatible]

98

CALIDAD MÁXIMA

Amazon.es

DollaTek

DollaTek 5pcs SR501 módulo de Sensor Humano piroeléctrico infrarrojo PIR Motion Detector módulos

96

CALIDAD SUPERIOR

Amazon.es

AZDelivery

AZDelivery 5 x HC de módulo ultrasónico hc-SR04 telémetro Sensor Compatible con Arduino y Raspberry Pi con eBook Incluido

93

CALIDAD EXCELENTE

Amazon.es

AZDelivery

AZDelivery Kit de Iniciación ESP32 Dev Kit C NodeMCU - HC-SR501 PIR Detector de Movimiento con Mini Breadboard Compatible con Arduino con E-Book Incluido!

90

CALIDAD DISTINGUIDA

Amazon.es

Hailege

Hailege 5pcs PIR Infrared Sensor Human Body Infrared Motion Module for Arduino Raspberry Pi

84

CALIDAD FIABLE

Amazon.es

HiLetgo

HiLetgo 5pcs PIR 501 Infrared Sensor Human Body Infrared Motion Module for Arduino Raspberry Pi

81

CALIDAD BUENA

Amazon.es

TR Computers

Sensor de movimiento PIR y clip GPIO para Raspberry Pi Zero W, Pi 3, Pi 2, B+, A+, B y A. Se conecta directamente a pines GPIO. El módulo HC-SR501 PIR envía señales en GPIO4.

80

CALIDAD BUENA

Amazon.es

HiLetgo

HiLetgo 3pcs AM312 Mini Pyroelectric PIR Human Sensor Module PIR Infrared IR Sensor Body Manual Motion Infrared IR Detector

77

CALIDAD BUENA

Amazon.es

TECNOIOT

2pcs SR501 HC-SR501 HCSR501 Adjust IR Motion Sensor

74

CALIDAD BUENA

Amazon.es

BEMATIK.COM

BeMatik - Sensor Detector de Movimiento PIR piroeléctrico Infrarrojos HC-SR501

65

CALIDAD BUENA

Amazon.es